| Item: |
170-50 |
| Description: |
Dynamic
HTHP Filter Press, 115 Volt |
The OFITE Dynamic High Temperature High
Pressure (HTHP) filter press measures filtration properties under varying dynamic downhole conditions. A motor-driven shaft fitted with propellers turns at varying speeds inside a standard 500 ml
HTHP cell. RPM settings from 1 to 1600 RPM impart laminar or turbulent flow to the fluid inside the cell. By varying the shaft length, the shear stress may be increased or decreased. The power is driven to the stirring shaft by a timing belt that is easily accessible for quick adjustment and removal. Other features include a variable-speed motor controlled through an SCR controller. RPM is indicated on a digital tachometer. The test procedure is exactly the same as that in the conventional
HTHP filtration test. The only difference is the fluid is circulating inside the cell while filtrate is being collected. Since the filter medium is conventional disk material, the results are fully comparable with those of other laboratories or for comparing historical trends.
Features of the Dynamic Filter Press Include:
- Analyzes fluid in motion
- Variable-speed electric motor, 1/2 HP permanent magnet DC
- Auxiliary pipe connection for the cell top cap. Plug may be removed to add additional fluid additives.
- Safety calibrated rupture disk to guard against overpressure
- Motor and stirring shaft rpm operate at a one-to-one ratio
- Adjustable thermostat from 100 to 500°F
- Optional filter permeabilities available
- 500 ml capacity stainless steel cell
- Optional carrying case
Size: 12 x 15.5 x 36 inches (30.5 x 39.4 x 91.4 cm)
Weight: 95 lbs (43.1 kg)
Components:
1 #135-18 Set Screw Socket for Clamp
1 #153-12 Graduated Cylinder, Glass, 100 ml x 1 ml
1 #154-06 Full Scale Thermometer, LED Disp, -58-500°F
1 #165-44 High Temp Thread Lubricant, 1 oz
1 #170-71 Pipe Plug, NPT, 316 SS, 1/8"
1 #170-78 Retaining Ring Pliers, Internal
1 #170-79 Retaining Ring Pliers, External
1 #170-80 Mini-Jet Pump, 115 V. 60 Hz, 79-153 GPH
1 #170-81 Hex Adapter for Pump
2 #170-82 Quick Connect, Male
2 #170-83 Quick Connect, Female
4 #170-84 Tubing, Polyurethane, 1/8"
1 #170-85 T-Clip for Hoses
1 #170-86 Grease Fitting, NPT Straight, 1/8"
1 #291-06 Cylinder, Acrylic, 1 Liter
Cell Assembly Components:
6 #170-13-2 O-Ring F/Cell, Buna 90
2 #170-16 Valve Stem for Cell
6 #170-17 O-Ring for Valve Stem, Viton®
1 #170-19 Filter Paper, 2 1/2", 100/pkg
1 #170-23 Screen, 60 Mesh
12 #170-26 Cap Locking Screw, Stainless Steel
1 #170-27 Allen Wrench f/Cap Locking Screw, 5/32"
1 #170-35 Adjustable Wrench, 6"
10 #170-53 Ceramic Filt, 10 Darcy, 35 Micron, 2.5" x 1/4"
1 #170-67 Propeller, 1 1/2"
1 #170-68 Propeller, 2"
1 #170-69 Scribed Cell Cap f/Ceramic Disk (Outlet)
1 #170-72 Spacer for Filter Paper, SS, 1/4"
1 #170-73 Cell Cap f/Filter Paper Usage, 1 1/8” Thick
2 #170-77 O-Ring for Stainless Steel Spacer
1 #171-02 Cell Body, Dbl Cap, 10”, 500 ml, 2000 psi
Drive Assembly Components:
2 #140-60-01 O-Ring for Water Swivel Feed Tube
8 #170-54 Packing Ring, Carbon, 5/8" x 1/8"
12 #170-54-1 Packing Ring, Teflon, 5/8" x 1/8"
4 #170-56 Retainer Ring f/Water Swivel, External, 5/8"
2 #170-57 Retainer Ring f/Lower Seal Ring, Internal, 1 1/8"
1 #170-57-1 Retaining Washer, Stainless Steel, 1/8"
3 #170-61 Thrust Washer for Packing, Aluminum
1 #170-61-1 Thrust Bearing & Spacer, Bronze, 1/16"
1 #170-62 Lower Bearing for Shaft, Bronze
1 #170-63 Drive Belt, 5/8"
2 #170-64 O-Ring for Water Swivel
1 #170-65 Tubing, Water Inlet, 10 ft (older models)
1 #170-66 Adapter for 1/8" Tubing (older models)
2 #170-74 Retainer Ring f/Bearing Housing, Internal
1 #170-75 Ball Bearing for Bearing Housing
2 #170-76 Bearing Sleeve for Water Swivel, Bronze
Heating Jacket, Motor, and Stand Components:
1 #135-17 Switch Plate
1 #170-05 Thermostat, 50 - 500°F
1 #170-09 Insulation Board
1 #170-10 Pilot Light for Thermostat
4 #170-11 Heating Element, 115 Volt, 200 Watt
1 #170-29 Power Cord with Male Plug
2 #171-32 Midget Knob
1 #171-36 Thermostat Cover
4 #171-44 Rubber Foot, 3/4"
1 #171-71 Thermostat
1 #171-87 Location Pin
1 #171-94 Cell Rest Plunger Assembly
1 #174-23 Terminal Strip, 10 Place
Pressurization Assembly Components:
1 #140-60-01 O-Ring for Bleeder Valve
1 #171-10 Back Pressure Receiver, 100 ml
1 #171-24 Dual Nitrogen Manifold, 1350 & 750 psi
Optional:
1
#170-50-SP One Year’s Spare Parts for 170-50
1 #170-52 Carrying Case
1 #170-58 Shaft Extension, 1/2"
1 #170-59 Shaft Extension, 1"
1 #170-60 Shaft Extension, 1 1/2"
|
